Español
Français
- -30%
Water-based matt paint, especially formulated for concrete swimming pools. Easy appplication and quick drying. The paint film shows a high resistance to algae growth.
PAINT FOR SWIMMING POOLS SATIN WATER BASED. The paint film shows a high resistance to algae growth and mold ALP
€63.42
€44.39
Save 30%
Tax included
Water-based satin paint, especially formulated for concrete swimming pools. Easy appplication and quick drying. The paint film shows a high resistance to algae growth.
Main Properties
- Smoother odor than solvents pool paints
- Resistant to dilute acids and alkalis.
- Repaintable over acrylic paints and chlorocaucho
- Resistant to mold and algae
Recommended Uses
Interior and exterior walls and pavements of cement and concrete pools.
Surface treatment
- New surfaces: The new supports must not be painted before 1 month, in order that the concrete is completely set. Then make a wash to remove loose aggregates and contaminants. Then rinse with plenty of water and allow to dry completely for a minimum of 48 hours.
- Old surfaces: The surface must be cleaned and degreased. In already painted swimming pools, badly adhered or defective areas should be eliminated. If there are greenish or black spots it may be due to the presence of mold or algae, and they should be completely removed before painting the pool. Once the surface is prepared proceed as in the case of new surfaces.
Special Precautions: The pool will be clean and dry in any case. Do not paint if there is dew, or in full sun. Once painted the pool will remain empty for 1 to 2 weeks. This product is not suitable for painting tanks intended for the consumption of drinking water for both people and animals. Not suitable for painting polyester pools.
Appearance: Satin
Recommended Performance: 10-12 m² / l
Drying: 4 - 5 hours.
Repainting: From 12 hours.
Number of layers: Two or more layers depending on the porosity and color of the support.
Tools: Brush / Roller / Airless Pistol
Dilution: First hand dilute to a maximum of 10% with water. Second hand up to a maximum of 5% if necessary. For spray gun dilute to suitable viscosity.
Cleaning: Clean utensils with water immediately after use.
You might also like
Antidrop Super, smooth surfaces with acrylic latex paint. Very good covering power and superior polyamide, 11 mm.
- Very good covering power.
- Manufactured by thermofusion to avoid sewing points.
- Superior polyamide, 11 mm.
Recommended use: Smooth surfaces with acrylic latex paint
Bicolor 60 Padded, façades and outdor surfaces. Maximum covering power and 60 mm. diameter for maximum performance.
- Maximum covering power.
- 60 mm. diameter for maximum performance.
- Manufactured with internal polyurethane foam for berrer adaptation to irregular surfaces.
- 100% Extra long Polyamide 20 mm.
Recommended use: Façades and outdoor surfaces
Pre-accelerated thixotropic orthophthalic polyester resin. It is a highly recommended product for the manufacture, manufacture and repair of parts (can be combined with the use of fiberglass)
(Each unit of 1kg of product carries its catalyst, also included)
To repair joints and chipped tiles and tiles. Reconstruction of edges and access of swimming pools. Repair anchors stairs or fasten, floors and walls, stoneware. Waterproofing.
Filling of ceramic joints, terraces and floor tiles. Repair in swimming pools. Specially designed to fill and waterproof joints in floors and walls, ceramics with absorption capacity ≤ 3%, porcelain stoneware, vitreous mosaic, with natural stone platelets. Indicated to work in humid places like bathrooms, kitchens or swimming pools, in occasional or permanent contact with wate
5 other products in the same category:
Water-based matt paint, especially formulated for concrete swimming pools. Easy appplication and quick drying. The paint film shows a high resistance to algae growth.
Filling of ceramic joints, terraces and floor tiles. Repair in swimming pools. Specially designed to fill and waterproof joints in floors and walls, ceramics with absorption capacity ≤ 3%, porcelain stoneware, vitreous mosaic, with natural stone platelets. Indicated to work in humid places like bathrooms, kitchens or swimming pools, in occasional or permanent contact with wate
High performance cement based adhesive. Applicable on supports made with brick, cement, stone, concrete and fiber-cement. Specially designed to glued tiles on masonry surfaces.
To repair joints and chipped tiles and tiles. Reconstruction of edges and access of swimming pools. Repair anchors stairs or fasten, floors and walls, stoneware. Waterproofing.
Chat with us on WhatsApp
